Product Line

Dampney Engineered Coatings

Home » Endcor » Product Details
  

Corrosion resistant coatings include silicone alkyd, thermo setting epoxy,inorganic zincs, acrylic urethane, water borne silicone, coal tar epoxy, elastomeric, cold galvanizing compound.

Endcor® 8898

Silicone Alkyd Self Priming Coating

A high-performance, high solids, self priming, high gloss, hard, durable coating for use on cast steel surfaces. Coating is used on utility meters, valves, electrial meters, water meters, electrical boxes, pumps, machinery, motors, piping, fencing and storage tanks.
A high-performance, high solids, self priming, high gloss, hard, durable coating for use on cast steel surfaces. Complies with state VOC (Volatile organic content) emission control regulations. Compared to conventional alkyd paints it provides a wide range of improved properties, including: significantly improved gloss retention and chalking resistance, reduce color fade, continuous film integrity, and temperature resistance.
Features
 Long-term durability and weather resistance
 Excellent gloss and color retention
 Resistant to chalking, UV radiation, humidity, moisture, salt spray and chemical atmospheres
 Self priming corrosion protection
 Can be applied over solvent cleaned surfaces
Common Uses
 Cast valve bodies
 Cast iron and steel surfaces
 Structural steel, pipes, and tanks
 Low temperature stacks

Specification Data

Generic Type
Silicone Alkyd Copolymer
Color
Gray
Immersion
No
Components
1
Dry Film Thickness per coat
3.0 – 4.0 Mils (75 – 100 microns)
Wet Film Thickness per coat
5.0 – 7.0 Mils (125 – 175 microns)
Application Method
Brush|Roll
Theoretical Coverage
240 sq. ft. per gallon (5.89 m²/liter)
Curing Requirements
Drying time @ 77F (25C)
To touch - 2 hours
To recoat - 16 – 24 hours
Final cure - 7 days

Application Instructions

Surface Preparation
To ensure optimum long-term coating system performance, surfaces must be clean, dry and free from oil, grease, dirt, salts, welding flux, mill scale, rust corrosion products, oxides, old paint, visible and nonvisible contaminants or other foreign matter. After completion of preliminary surface preparation work, clean all surfaces following “SSPC-SP 1 solvent cleaning standard” using a non-film forming solvent such as Dampney 170 cleaning solvent.
Mixing
Redisperse any settled-out pigments by thorough mixing to a uniform homogeneous consistency with an explosion proof or air driven power mixer. Do not open containers until ready. Keep Lid on container when not in use. use adequate air pressure and volume to obtain proper atomization. Do not thin beyond federal, state and/or local VOC (volatile organic compound) emission regulations. Note: Use of other thinner not approved by Dampney may hinder product performance and void product warranty, whether expressed or implied.
Thinning
Only thin Endcor 8898 with Dampney 105 Thinner a maximum of 5% by volume. Dampney 105 thinner can be used if encountering dry spray and for other application related conditions. When reducing Endcor 8898 for viscosity use thinners cautiously. The addition of a small amount of thinner will cause a large reduction in coating viscosity. Excessive thinning will impair wet film thickness and will cause runs and sags and change the VOC content of the coating. For conventional spray use adequate air pressure and volume to obtain proper
atomization. Do not thin beyond federal, state and/or local VOC (volatile organic compound) emission regulations. Note: Use of other thinner not approved by Dampney may hinder product performance and void product warranty, whether expressed or implied.
Clean Up
Thoroughly flush all application equipment and hoses immediately after use with Dampney 105 Thinner. Dismantle spray equipment and clean parts and brushes with Dampney 105 Thinner.
Warning
FLAMMABLE LIQUID AND VAPOR.
Combustible Liquid and Vapor. Keep away from heat, sparks and flame. Vapors may cause flash fire. Do not breathe vapors or spray mist. Avoid contact with eyes, skin and clothing. Use with adequate ventilation during mixing and application. Wear an appropriate, properly
fitted organic vapor cartridge-type respirator (NIOSH approved) during and after application unless air monitoring demonstrates vapor/mist levels are below applicable limits. Follow respirator manufacturer’s directions for respirator use. Wash thoroughly after handling. Wear protective gloves, chemical safety goggles and impervious protective clothing. Use skin cream. In confined spaces it is required to use a positive pressure supplied-air respirator (NIOSH approved). Use explosion-proof lights and electrical equipment. Use only nonsparking tools and equipment. Wear conductive and nonsparking footwear. Make certain all electrical equipment is grounded. Observe all safety precautions and follow procedures described in OSHA regulations. See Safety Data Sheet (SDS) for complete precautionary and disposal information. If instructions and warnings cannot be strictly followed, do not use this product. If instructions and warnings cannot be strictly followed, do not use this product.
ORDER INFORMATION
  To place orders and/or obtain pricing information contact:

Dampney Company
85 Paris Street
Everett, MA 02149
TEL: (617) 389-2805
Request More Information
 
 

Product Lines

Thurmalox
Industrial high-temperature protective coatings.
Protexior
Industrial Coatings
Apexior
Coatings for resistance to boiling water/steam and waterside corrosion.
Dymacryl
Dymacryl masonry stains have a proven record of protecting surfaces against damage caused by water absorption.
Endcor
Corrosion resistant coatings include silicone alkyd, thermo setting epoxy,inorganic zincs, acrylic urethane, water borne silicone, coal tar epoxy, elastomeric, cold galvanizing compound.
Elastoid
Single package high build ELASTOMERIC coating and vapor barrier.
Epodur
Underwater epoxy coating, solvent free. Used for epoxy coatings, floor coatings and concrete restoration projects. Skid resistant epoxy broadcast floor system.
Alvin Products
Offering a complete line of quality problem-solving products for industry.
Stove Paint
Dampney has served the home and hearth industries for many years providing high performance heat resistant coatings to meet their ever changing needs. Visit www.StovePaint.com for more information.
Temperature Indicating Coatings
Silicone coatings designed primarily for temperature indicating applications requiring an irreversible sharp visual color change.